L'Antre Du Protecteur (2020) Mac OS

broken image


The Best Mac Antivirus Protection for 2021. Despite what you may have heard, your Apple computer is not immune to malware. We test the top contenders to identify those offering the best Mac. Which Mac operating systems (OS) do these antiviruses protect? In general, most antivirus products will be available for OS X 10.10 and later. There are certain instances where newer Macs and operating systems benefit from better service. For instance, my top free antivirus for Mac, Avira, is only available for OS X 10.13 and later.

A GCode Analyzer for 3D printing is now available. This on-line tool estimates the amount of filaments required and the cost to print a 3D object.

4 Digits Nixie Tube Clock Stand

This is a 15 mm in height stand for a 4 Digits Nixie Tube Clock. This clock is available on AliExpress. The base of the clock is 40 mm

Read More

Another Pen Holder

This is a pen holder of an unusual design. Three sizes are available. You can increase the capacity of them by gluing another one on its side. Support is

Read More

How to move a directory from one git repository to another one preserving the history

These simple steps will let you move a directory contained within a git repository into another one while preserving the history. Make the root directory of the source git repository

Read More

Waveshare Pi Pico Dual Expander Base Plate

This is a baseplate for the Waveshare Pi Pico Dual Expander. You will need 4 tiny screws to mount it. An infill of 15% is recommended. Support is not

Read More

1802 Membership Card Stand

This is a simple stand for the 1802 (COSMAC ELF) Membership Card. The 1802 is a vintage micro-processor. You can get this kit at http://www.sunrise-ev.com/1802.htm . I'm not affiliated

Read More

LG 27EA33 Storage Trays

This is a tray designed to be installed on the stand of an LG 27EA33 monitor. You need to print the STL file provided and the same file mirrored. You

Read More

Panavise 303 replacement pads

This is pad replacements for the Panavise 303 vise. It has groves to hold tubular objects. I've printed it in semi-flexible filament but works fine printed in PLA. Support is

Read More

SBC Server Case

This is a modular SBC or Development Board enclosure. Its base design principle is you stack on top of each other plates that hold various devices such as Raspberry

Read More

3.5 inch Hard Drive Box

This is a box for a 3.5 inch hard drive and its cover. It was specifically designed to fit in a small safety box often rented by banks. Support

L
Read More

Electronic Bench Organizer

This is an organizer especially designed for an electronic bench to hold small parts, screws, etc. Support is not needed. This object was designed using Solid Edge Community Edition.

Read More

Magazine File

This a magazine file 60 mm wide. It is designed for letter size paper. It is by design a bit smaller than the document it holds. It has holes

Read More

CR-10 Under Bed Tray

These are trays to put under a CR-10 3D printer. The separator of one tray are 15 mm in height. For the other one, 38 mm in height which

Read More

Hanging Open Box

Ball run (itch) mac os. This is an open box that can be hanged using 2 screws. The diameter of the head of the screw must be less than 1 cm. Its dimensions are

Read More
Protecteur
Read More

Electronic Bench Organizer

This is an organizer especially designed for an electronic bench to hold small parts, screws, etc. Support is not needed. This object was designed using Solid Edge Community Edition.

Read More

Magazine File

This a magazine file 60 mm wide. It is designed for letter size paper. It is by design a bit smaller than the document it holds. It has holes

Read More

CR-10 Under Bed Tray

These are trays to put under a CR-10 3D printer. The separator of one tray are 15 mm in height. For the other one, 38 mm in height which

Read More

Hanging Open Box

Ball run (itch) mac os. This is an open box that can be hanged using 2 screws. The diameter of the head of the screw must be less than 1 cm. Its dimensions are

Read More

3D Printing Trashcan

This is a small trashcan for 3D printing. The way the cover is designed, plastic stuff in the trashcan won't spring back outside it. The trashcan is 80 mm

Read More

Issues with Ubuntu 20.04 on AMD Ryzen 7 4800H and GeForce GTX 1660 Ti

UPDATE: Ubuntu 20.10 fixes the issues listed below. ASUS came out recently with very powerful gaming laptops at a very good price. The hardware is quite recent. Installing Linux on

Read More

Parametric Round Container

The decent of jacobs ladder mac os. It is a simple parametric round container. Open the ParametricBox.scad file with openScad ( http://www.openscad.org/ ) Modify the variables in Parameters.scad to suit your needs and save it. Open

Read More

Wires And Probes Hanger

This object will let you suspend your wires and probes on a door. To complete this assembly, you will need a pipe or tube of 5/8 in or 16

Read More

L'antre Du Protecteur (2020) Mac Os X

Drawer Dividers for Small Parts Cabinet

These are small drawer dividers. There are 2 models. One for the drawer cabinet sold by Canadian Tire. The other one is for drawer cabinet sold by Home Depot.

Read More

20mm Extrusion Vibration Absorber

This is an anti-vibration foot for 20mm aluminum extrusion. I had good results using semi-flexible filament. I added some anti-sliding pad. A boring game 2 mac os. They were specifically designed for an Ender-3 printer.

Read More

L'antre Du Protecteur (2020) Mac Os Downloads

Kotto Fume Extractor Stand

This is a stand for the Kotto Fume extractor that can be bought from Amazon. It raises the fume extractor by 3 cm. It can be printed without support.

L'antre Du Protecteur (2020) Mac Os Catalina

Read More



broken image